MCQ
21121. A beam is a structural member subjected to loads.
axial
tansverse
axial and transverse
21122. The beams resting on purlins are known as-
spandrel beams
rafters
trimmers
stringers
21123. The maximum allowable stress for rolled steel beams and channels is-
128.5 MPa
181.5 MPa
156.5 MPa
228.5 MPa
21124. The beams supporting the stair steps are called as-
spandrel beams
trimmers
rafters
stringers
21125. The main beam is a beam, which supports-
floor construction
joists
secondary beam
none of these
21126. Any major beam in a structure is known as a-
subsidiary beam
joist
girder
secondary beam
21127. The bearing capacity of a soil-with the decrease in the area of the footing. (মাটির ভারবহন ক্ষমতা ভিত্তির ক্ষেত্রফল হ্রাসের সাথে)
increases
same as
decreases
none of these
21128. The shear stress in a beam at neutral axis is-
zero
maximum
minimum
21129. If the coefficient of passive earth pressure 1/3, then the coefficient of active earth pressure is- (যদি নিষ্ক্রিয় চাপের গুণক 1 3 হয় তবে সক্রিয় চাপের সহগ কত হবে?)
1/3
3/2
1
3
21130. In case of footings in sand, if the soil pressure distribution is triangular, the maximum soil pressure is the average soil pressure. (বালিতে ফুটিং ক্ষেত্রে যদি মাটির চাপ বিতরণ ত্রিভুজকার হয়, তবে মাটির সর্বোচ্চ চাপ হবে.... মাটির গড় চাপের)
equal to
four times
three times
double
21131. The co-efficient of earth pressure at rest stiff clay is about- (পৃথিবীর স্থির চাপের সহগ শক্ত মাটির সমান)
0.4
0.6
0.5
0.8
21132. A dry sand specimen is put through a triaxial test. The cell pressure is 50kPa and the deviator stress at failure is 100kPa. The angle of internal friction for the sand specimen is-
15°
35°
30°
40°
21133. According to SI code, the total settlement of isolated footings for cohesive soil should be- (এসআই কোড অনুসারে, সংশক্তিপ্রবণ মাটির বসন হওয়া উচিত।)
30mm
40mm
50mm
65mm
21134. The bearing capacity factors Ne, Na & Ny are functions of- (ভারবহন ক্ষমতা ফ্যাক্টর Ne, Nq, & Nr- এর কাজ)
cohesion of the soil
friction angle
internal friction angle
both a & b
21135. The process of obtaining increased density of soil in a fill by reduction of its pore space by the expulsion of air, is known as- (বায়ু সরিয়ে মাটির ছিদ্র স্থান হ্রাস করে ভরাট মাটির ঘনত্ব বৃদ্ধির প্রক্রিয়াকে কী বলা হয়?)
soil exploration
soil stabilisation
soil compaction
consolidation
21136. Which of the following is not a tension member?
Cable
Tie
Bar
Boom
21137. The maximum deflection, for a simply supported beam, should not exceed-
1/125 of span
1/225 of span
1/325 of span
1/425 of span
21138. The process of maintaining or improving the performance of a soil as a constructional material, usually by the use of admixtures, is known as- (অ্যাডমিক্সচার ব্যবহার করে নির্মাণ সামগ্রী হিসাবে মাটির কার্যক্ষমতা বজায় রাখা বা উন্নত করার প্রক্রিয়া হিসাবে পরিচিত)
soil exploration
soil stabilisation
soil compaction
consolidation
21139. When the water table is close to the ground surface, the bearing capacity of soil is reduced to- (যখন ওয়াটার টেবিল ভূপৃষ্ঠের কাছে আসে তখন মাটির ভার বহন ক্ষমতা হ্রাস পেয়ে)
one-fourth
one-half
two-third
three-fourth
21140. The unit bearing capacity of footing in sand- (বালিতে ফুটিং-এর ভারবহন ক্ষমতা।)
decreases with depth of footing
decreases with width of footing
increases with depth of footing
increases with width of footing