সার্ভেয়িং MCQ
সিভিল ডিপার্টমেন্টের "" সার্ভেয়িং "" সাবজেক্টের সকল MCQ এখানে পাবেন। Civil Engineering এর চাকরি প্রস্তুতির জন্য ডিপার্টমেন্ট ও নন-ডিপার্টমেন্টের সকল MCQ এর প্রশ্ন উত্তর ব্যাখ্যাসহ এখানে পাবেন। সহকারী/উপ-সহকারী প্রকৌশলী চাকরি প্রস্তুতির জন্য আমাদের App: Engineering Classroom গুগল প্লে-স্টোর থেকে ডাউনলোড করে নিন। Surveying all MCQ, Civil Engineering MCQ
261. 15m-এর কম দৈর্ঘ্যের অফসেটকে বলে-
শর্ট অফসেট
লং অফসেট
প্লাস অফসেট
আয়তাকার অফসেট
ব্যাখ্যা: 15m-এর বেশি দৈর্ঘ্যের অফসেটকে লং অফসেট এবং 15m- এর কম দৈর্ঘ্যের অফসেটকে শর্ট অফসেট বলে।
262. The instrument attached to the wheel of a vehicle in order to measure the distance travelled, is called-[BADC-18]
passometer
pedometer
odometer
speedometer
ব্যাখ্যা:
263. The error in measured length due to incorrect holding of chain is- [BADC-18]
compensating error
cumulative error
instrumental error
negative error
ব্যাখ্যা: জরিপকালে শিকলের (ফিতার) দৈর্ঘ্য যদি একবার বাড়ে আবার কমে, অথবা একবার কমে আবার বাড়ে, তাহলে ঐ ধরনের ভ্রান্তিকে ক্ষতিপূরক ভ্রান্তি (Compensative error) বলে।
264. Contour lines cross ridge or valley lines at-[BGFCL-17]
30°
60°
45°
90°
ব্যাখ্যা:
265. স্টেশন বিন্দু নির্বাচন করতে হবে-
চৌহদ্দির ভিতরে
চৌহদ্দির বাইরে
চৌহদ্দির ভিতরে অথবা বাইরে
জরিপ এলাকার কেন্দ্রে
266. জরিপের প্রারম্ভেই করতে হয়-
স্টেশন বিন্দু নির্বাচন
স্টেশন চিহ্নিতকরণ
পর্যবেক্ষণ জরিপ
পরিমাপ গ্রহণ
267. Plane and geodetic surveying are classification of surveying based on : [HED-19]
Methodology
Earth's curvature
Object of survey
Instrument
ব্যাখ্যা: Plane and geodetic surveying based on the considerations and true shape of the earth. Plane surveying assumes the earth is flat and geodetic
surveying the curvature of the earth.
268. জরিপ এলাকার সমতল ভূমির ওপর নির্বাচিত দীর্ঘ রেখার নাম-
ভিত্তিরেখা
শিকল রেখা
গ্রন্থিরেখা
যাচাই রেখা।
269. A fixed point reference of known elevation is called-[MES-16, 18/
change point
station point
benchmark
datum
ব্যাখ্যা:
270. In an optical square, the angle between the first incident ray and the last reflected ray is- [MES-18, MOCA-19]
60°
90°
120°
150°
ব্যাখ্যা: অপটিক্যাল স্কয়ারের First incident ray last incident ray-এর মধ্যবর্তী কোণের মান 90°।
271. The method of measuring distance by pacing is S chiefly used in-[BADC-18]
reconnaissance survey
preliminary survey
location survey
all of these
ব্যাখ্যা:
272. An angle between the inclined line of sight and the horizontal is called- [BADC-18]
direct angle
vertical angle
horizontal angle
deflection angle
ব্যাখ্যা: If the object is below the horizontal, then the angle
between the line of sight and the horizontal is called the angle of depression
273. কোন অফসেটে দুটি চেইনেজ উল্লেখ করতে হয়?
তির্যক অফসেট
লম্বিক অফসেট
প্লাস অফসেট
মাইনাস অফসেট
274. When the measured length is less than the actual length, the error is known as-(MOCA-19]
positive erroг
negative error
compensating error
none of these
ব্যাখ্যা: Negative errors (making the measured lengths less than the actual) may be caused because the length of the tape or chain may be greater than the standard because of the wear or flattening of the connecting rings, opening of ring joints, temperature higher than the one at which it was calibrated.
275. The representative fraction 1/2500 means that the scale is- [BADC-18]
1cm = 0.25m
1cm = 2.5m
1cm = 25m
1cm = 250m
ব্যাখ্যা: 1/2500 means 1 cm = 2500 ст Hence, 1 cm = 25 m
276. স্টেশন বিন্দু নির্বাচনে প্রাধান্য দিতে হয়-
সীমানা
গ্রন্থিরেখা
পরিদৃশ্যতা
আবহাওয়া
277. A line joining some fixed points on the main survey lines, is called a-[MES-18]
check line
baseline
tie line
none of these
ব্যাখ্যা:
Line joining some fixed points as a tie station on the main survey line is called as tie line.
278. What is the length of each link of a 20m long chain? [BREB-17]
100mm
200mm
300mm
400mm
ব্যাখ্যা: চেইন 100 ভাগে ভাগ থাকে 20 x 1000 /100 = 200mm 100
279. A plain scale is used to read-[BADC-18]
one dimension
two dimension
three dimension
all of these
ব্যাখ্যা:
280. The error in measured length due to sag of chain or tape is known as--[BADC-18]
positive error
negative error
compensating error
instrumental error
ব্যাখ্যা: The error in measured length due to careless holding of chain is cumulative error. When the pull applied while measuring with a tape, is more than the standard pull for that tape, the error in measured length is positive.