MCQ
81. Screw thead-এর Major dia. ও Minor dia-এর পার্থক্য-
Depth of thread
Depth of teeth
Pitch
Whole depth
82. একটি আয়তাকার ক্যান্টিলিভার বিমে ৪ টি 20mm bar ব্যবহার করা হয়েছে। যদি fs = 140Mpa, f'c=21 Mpa হয়, তবে ঐ রডগুলোর Embedment দৈর্ঘ্য cm এককে কত হবে?
36.5
39.23
45.25
কোনটিই নয়
83. Retaining Wall সাধারণত প্রয়োজন হয়-
For Hill Road
Masonry Dams
Wing Wall
For all of them
84. The load on a spring per unit deflection, is called --
Stiffness
Proof resilience
Proof stress
Proof load
85. একটি বিমের উপর Linearly distributed load থাকলে তার Shear Force Diagram এর আকৃতি কীরূপ হবে?
Linear
Parabolic
Cubic
কোনোটি নয়.
86. 250mm Rod কে 50kN বল দিয়ে টানলে তা যদি 0.3mm বর্ধিত হয় তাহলে Strain-এর মান কত?
0.0125
0.012
0.0012
0.0015
87. A material is said to be perfectly elastic if--
It regains its original shape on removal of the load
It regains its original shape partially on removal of the load
It does not regain its original shape at all
None of these
88. A shaft rotating N.R.M. under a torque T, transmits a power--
/30 Newton metres/sec
/30 Newton metres/min
/60 Newton metres/min
/60 Newton metres/sec
89. একটি বিমের উপর Uniformly distributed load থাকলে তার Bending Moment diagram এর আকৃতি কীরূপ হবে?
Linear
Parabolic
Cubic
কোনোটিই নয়
90. A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial load W, the energy stored in the spring, is
4WD^2 n/d 4N
4W^2 Dn/d 4N
4W^2D3n/d 4N
4W^2D3n²/d 4N
91. Retaining wall design-4 Bearing capacity এর জন্য অন্তত কত Factor of Safety রাখা উচিতায়-
2
2.5
3
4
92. A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2. These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2, the stresses developed are:
b=10 N/mm2 s = 20 N/mm2
b=8 N/mm2 s = 16 N/mm2
b=6 N/mm2 s = 12 N/mm2
b=5 N/mm2 s 10 N/mm2
93. The moment of inertia of a triangular section (height h, base b) about its base, is--
bh²/12
b^2h /12
bh^3 /12
b^3 h/12
94. The degree of indeterminacy of the frame in the given figure, is --
1
2
3
Zero
95. Linear এবং Lateral strain এর অনুপাতকে কী বলে?
Bulk modulus
Modulus of elasticity
Poisson ratio
Modulus of toughness
96. ACI কোড অনুসারে খ কার্যকরী দৈর্ঘ্যবিশিষ্ট Cantilever Slab- এর নূন্যতম পুরুত্ব কত হবে ?
L/12
L/6
L/20
L/24
97. RCC Column কে Short Column হিসেবে ধরা হবে যখন এর slenderness ratio-
৩০ এর কম হবে
৩৫ এর কম হবে
৪০ এর কম হবে
৫০ এর কম হবে
98. IF Q is load factor, S is shape factor and F is factor of safety in elastic design, the following:
Q=S+F
Q=S-F
Q=F-S
Q=S*F
99. শক্তি প্রয়োগের দিক বরাবর একটি Bar-এর যে পরিবর্তন হয় তাকে কী বলা --
Linear Strain
Lateral Strain
Volumetric Strain
Shear Strain