MCQ
1141. What is meant by drag in casting process?
Upper part of casting flask
Molten metal
Lower part of casting flask
Upper and lower part of casting flask
1142. ফায়ার টিউব বয়লারে-
পানি উত্তপ্ত টিউবের মধ্য দিয়ে প্রবাহিত হয়
আগুন টিউবের মধ্যে থাকে
পানি ও আগুন উভয়ই টিউবের মধ্যে থাকে
উপরের কোনোটিই সঠিক নয়
1143. Which of the following material is not made by injection molding?
Nuts
Car handles
Tubes
Electrical fittings
1144. Which of the following non-metallic material is not used in the synthesis of molds?
Magnesite
Zircon
Silimanite
Valcanised rubber
1145. Nitriding process is used to increase surface hardness for which of the following materials?
Alloy steels
Low carbon steels
Medium carbon steels
High carbon steels
1146. Which of the following pattern making machine makes wooden board?
Jointer
Mortiser
Drill press
Scroll saw
1147. নিচের কোন বয়লারটি ফায়ার টিউব?
ল্যাংকাশায়ার বয়লার
ব্যাবকক (Babcock) অ্যান্ড উইলকক্স বয়লার
স্টারলিং বয়লার
ভেলোকস বয়লার
1148. কোনটি ফায়ার টিউব বয়লার?
ল্যামন্ট বয়লার
বেনসন বয়লার
কোচরান বয়লার
সবগুলো
1149. The shrinkage allowance for metal casting varies by the type of-
pattern
material
mould
metal
1150. হিট এক্সচেঞ্জারের অপর নাম কী?
স্টিম জেনারেটর
কন্ডেন্সার
রিয়্যাক্টর
মডারেটর
1151. What is the minimum temperature allowed to be given to the injection molding process?
120°C
130°C
140°C
150°C
1152. ঢালাইলোহার ক্ষেত্রে বালির পারমিয়্যাবিলিটি কত হওয়া উচিত?
20-30.cc/min
40-50 cc/min
30-40 cc/min
50-60 cc/min
1153. নিচের কোনটি কুশন অ্যাডিটিভস-এর উপাদান?
কাঠের গুঁড়া
সিলিকা
সী-করলা
গ্রাফাইট
1154. Which of the following factors is not considered in a ram type injection molding?
Inner pressure of material
Outer pressure of material
Volume of material
Temperature of material
1155. Which of the following is not a source of moulding sand?
Sea
Lakes
Desert
Forests
1156. পারমিয়্যাবিলিটির একক কী?
m/kg
mg/m²
cc/min
কোনোটিই নয়
1157. Where does the granular molding material get loaded into?
Barrel
Hopper
Pellets
Split
1158. ফিডওয়াটারের মধ্যে দূষিত বস্তু থাকলে বয়লারের নিচের কী অসুবিধা হয়?
স্তর জমা
ক্ষয়
ভঙ্গুরতা
সবক'টি
1159. What is the minimum pressure allowed to be given to the injection molding process?
90 MPa
140 MPa
100 MPa
170 MPa
1160. How is the die used in injection molding cooled?
Oil
Air
Water
Contact with cold surface