MCQ
2541.
If the ac supply is 50Hz, what will be the ripple frequency out of the full wave rectifier?
50Hz
100Hz
60Hz
20Hz
2542.
The most commonly used semiconductor is-
germanium
carbon
sulphur
silicon
2543.
A zener diode is destroyed if it-
is forward biased
is reverse biased
carriers more than rated current
none of the above
2544.
For highest power gain, one would use-- configuration.
CE
CB
CC
none of these
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: For highest power gain, CE configuration is used. In CE configuration, biasing capacitor is used to balance the operating point to obtain highest power gain
2545.
The battery connections required to forword bias a pn junction are-
+ve terminal to p and -ve terminal to n
-ve terminal to pand+ ve terminal to n
-ve terminal to p and-ve terminal to n
+ve terminal to pand+ ve terminal to n
2546.
The output frequency of a full wave rectifier is-
Same as the input frequency
One-half of the input frequency
Double of the input frequency
Independent of the input frequency
2547.
1 db corresponds to --- changes in voltage level.
12%
20%
80%
26%
2548.
Noise factor of a ideal amplifier is---
0dB
5dB
0.5dB
10dB
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: There is no noise in a ideal amplifier. So, noise factor is 0 dB
2549.
Approximately how many milliamperes of current flow through circuit with a 40V source and 6.8 ΚΩ of resistance?
27.2 mA
5.9 mA
59 mA
590 mA
2550.
Which causes the barrier layer in a PN Junction--
doping
barrier potential
recombination
ions
2551.
A voltage divider consists of two 100k resistors and a 12V source. What will the output voltage be if a load resistor of 1 MQ is connected to the output?
0.57V
12V
5.7 V
6 V
2552.
A PN junction acts as a--
unidirectional switch
bidirectional switch
controlled switch
none of the above
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: The PN junction is conduct with forward bias only. It means they conduct in only one direction (Current flows from P to N) That's why PN Junction acts as unidirectional twitch
2553.
As the temperature of a transistor goes up the base-emitter resistance-
decreases
increases
remains the same
none
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: As temperature increase, the thermal runway properly of transistor becomes more prominent and base-emitter resistance will decreases.
2554.
The purpose of a gate is to---
deliver molten metal into the mold cavity.
act as a reservoir for the molten metal.
feed the molten metal to the casting in order to compensate for the shrinkage.
deliver molten metal from pouring basin to gate
2555.
In the normal operation of an SCR, anode is-- with respect to cathode.
at zero potential
negative
positive
none of the above
2556.
The reverse current in a diode is of the order of—
KA
A
mA
uA
2557.
An SCR has PN junctions.
Two
Four
Three
None of the above
2558.
RC coupling is used for---amplification.
voltage
power
current
none
2559.
The point of intersection of de and ac load lines is called-
saturation
operating
cut off
none of these
2560.
An SCR has-semiconductor layers.
Two
Three
Four
None of the above