MCQ
1. স্ট্যাবিলিটি ফ্যাক্টরের আদর্শ মান--
200
1
100
500
2. An SCR is made of---
Germanium
Carbon
Silicon
None of the above
3. An SCR is a solid state equivalent of-
Triode
Gas-filled triode
Pentode
Tetrod
4. ইলেকট্রনিক্স কাজের জন্য আদর্শ সোল্ডারিং হলো-
25 watt
40 watt
30 watt
60 watt
5. PCB-এর ফুল মিনিং-
Pakistan Cricket Board
Printed Circuit Board
Painted Crossed Board
কোনোটিই নয়
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: PCB = Printed Circuit Board
6. An SCR has three terminals viz-
anode, cathode, grid
cathode, anode, gate
anode, cathode, drain
none of the above
7. --এ সূচনা বিন্দু (Operating point) সবচেয়ে বেশি স্থির থাকে।
ভোল্টেজ বিভাজিত (Divider) বায়াসিং
বেস-রোধ বায়াসিং
কালেক্টর-রোধ বায়াসিং
শূন্য বায়াসিং
8. In an SCR circuit, the angle of conduction can be changed by-
Changing anode voltage.
Changing gate voltage.
Reverse biasing the gate.
None of the above
9. If firing angle is increased, then the output of an SCR-
Remains the same
Is increased
Is decreased
None of the above
10. An SCR is made of silicon and not germanium because silicon-
is inexpensive
is mechanically strong
has small leakage current
is tetravalent
11. সাবমার্জড আর্ক ওয়েল্ডিং কোনটি ব্যবহৃত হয়?
Blanket flux
Basic flux
Luminous flux
Electric flux
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Digital electronics mcq
ব্যাখ্যা: সাবমার্জড আর্ক ওয়েল্ডিং-এ Blanket of granular flux ব্যবহার হয়ে থাকে।
12. AC power in a load can be controlled by connecting-
Two SCRs in series
Two SCRs in parallel
Two SCRs in parallel opposition
None of the above
13. An SCR behaves as a—switch.
Unidirectional
Mechanical
Bidirectional
None
14. ক্লাস 'ডি' অ্যামপ্লিফায়ারের কর্মদক্ষতা-
25%
50%
90%
60%
15. When SCR starts conducting, which loses all control?
Cathode
Anode
Gate
None of the above
16. An SCR is also known as---
Triac
Diac
Unijunction transistor
Thyristor
17. প্যার্টানে ড্রাফট কেন ব্যবহার করা হয়?
Remove pattern hardly
Remove pattern easily
Remove pattern quickly
কোনোটিই নয়
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Digital electronics mcq
ব্যাখ্যা: ড্রাফট (Draft): প্যাটার্নের খাড়া তলে ট্যাপার আকৃতির যে বাড়তি অংশ থাকে, তাকে ড্রাফট বলে। মোল্ড হতে প্যাটার্নকে উত্তোলন করার সময় মোল্ড গর্তের কিনারা ভেঙে যেতে পারে। সুতরাং মোল্ডের ক্ষতিসাধন না করে সহজে মোল্ড হতে প্যাটার্নকে উত্তোলন করার জন্য ড্রাফট দেওয়া হয়।
18. If gate current is increased, then anode-cathode voltage at which SCR turns ON-
is decreased
remains the same
is increased
none of the above
19. অপরিবাহীর এনার্জি গ্যাপ প্রায়-
15 eV
10 eV
0.7 eV
7 eV
20. ফিন্টারের আউটপুট থেকে পাওয়া যায়-
পিউর ডিসি
পালসেটিং ডিসি
পিউর এসি
এসি