সার্ভেয়িং MCQ
সিভিল ডিপার্টমেন্টের "" সার্ভেয়িং "" সাবজেক্টের সকল MCQ এখানে পাবেন। Civil Engineering এর চাকরি প্রস্তুতির জন্য ডিপার্টমেন্ট ও নন-ডিপার্টমেন্টের সকল MCQ এর প্রশ্ন উত্তর ব্যাখ্যাসহ এখানে পাবেন। সহকারী/উপ-সহকারী প্রকৌশলী চাকরি প্রস্তুতির জন্য আমাদের App: Engineering Classroom গুগল প্লে-স্টোর থেকে ডাউনলোড করে নিন। Surveying all MCQ, Civil Engineering MCQ
221.
In a direct vernier, the smallest division of a vernier is - the smallest division of its primary scale.
equal to
shorter than
longer than
d none of these
222.
The correction to be applied to each 30m chain for a line measured along a slope of 0 is-
30 (1- sine)
30 (1-cose)
30 (1-tane)
30 (1-cote)
ব্যাখ্যা: ঢালজনিত সংশোধনী, C₁ = L (1-cose).
223.
The obstacle, which obstructs vision but not chaining, is a-
river
pond
hill
all of these
224.
If the fore bearing of a line is its back bearing will be
36°15′.
126°15′
143°45′
216°15′
225.
A scale which has a common representative fraction, but read in different measures, is called- a
a plain scale
a diagonal scale
a shrunk scale
a comparative scale
ব্যাখ্যা:
226.
A line joining the apex of a triangle to some fixed points on the opposite side is called a-
30°
40°
50°
60°
227.
In a whole circle bearing system N25°15′W corresponds to-
115°15′
154°45′
205°15′
334°45′
228.
An average length of a pace is-
60cm
80cm
100cm
120cm
229.
When the length of a chain along a slope of 0 is L, the correction for slope required is-
I sin²θ/2
I cos²θ/2
2I sin²θ/2
2I cos²θ/2
230.
A diagonal scale is used to read dimensions.
two
three
four
five
231.
The angle between the reflecting surfaces of a prism square is-
30°
45°
60°
75°
232.
The angle of intersection of the horizon glass and index glass in an optical square is-
30°
45°
60°
75°
233.
A French cross-staff has a magnetic compass at the top.
Right
Wrong
234.
If the fore bearing of a line is 36°15′, its back bearing will be-
36°15′
126°15′
143°45′
216°15′
ব্যাখ্যা: সম্মুখ বিয়ারিং ও পশ্চাৎ বিয়ারিং-এর মাঝে পার্থক্য ১৮০০ হয়।
235.
An open cross-staff is commonly used for setting out-
short offsets
long offsets
oblique offsets
none of these
236.
The obstacle, which obstructs chaining but not vision, is a-
river
pond
hill
all of these
237.
In a prismatic compass, the zero of the graduated ring is located at-
north end
east end
south end
west end
238.
Compensating errors that occur in chaining are proportional to-
L
√L
1/L
1/√L
239.
Cumulative errors that occur in chaining are proportional to-
L
√L
1/L
1/√L
240.
The tension, at which the effects of pull and sag for a tape are neutralized, is known as-
initial tension
absolute tension
surface tension
normal tension
ব্যাখ্যা: