MCQ
5501.
1 db corresponds to --- changes in voltage level.
12%
20%
80%
26%
5502.
In an LC oscillator, the frequency of oscillation is:
Proportional to LC
Proportional to square root of LC
Inversely proportional to the square root of LC
Independent of the value of LC
5503.
The output frequency of a full wave rectifier is-
Same as the input frequency
One-half of the input frequency
Double of the input frequency
Independent of the input frequency
5504.
An SCR has PN junctions.
Two
Four
Three
None of the above
5505.
Transistor biasing represents --conditions.
ac
both ac & dc
dc
none
5506.
The purpose of a gate is to---
deliver molten metal into the mold cavity.
act as a reservoir for the molten metal.
feed the molten metal to the casting in order to compensate for the shrinkage.
deliver molten metal from pouring basin to gate
5507.
A PN junction acts as a--
unidirectional switch
bidirectional switch
controlled switch
none of the above
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: The PN junction is conduct with forward bias only. It means they conduct in only one direction (Current flows from P to N) That's why PN Junction acts as unidirectional twitch
5508.
In the normal operation of an SCR, anode is-- with respect to cathode.
at zero potential
negative
positive
none of the above
5509.
A voltage divider consists of two 100k resistors and a 12V source. What will the output voltage be if a load resistor of 1 MQ is connected to the output?
0.57V
12V
5.7 V
6 V
5510.
RC coupling is used for---amplification.
voltage
power
current
none
5511.
Which causes the barrier layer in a PN Junction--
doping
barrier potential
recombination
ions
5512.
For highest power gain, one would use-- configuration.
CE
CB
CC
none of these
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: For highest power gain, CE configuration is used. In CE configuration, biasing capacitor is used to balance the operating point to obtain highest power gain
5513.
The battery connections required to forword bias a pn junction are-
+ve terminal to p and -ve terminal to n
-ve terminal to pand+ ve terminal to n
-ve terminal to p and-ve terminal to n
+ve terminal to pand+ ve terminal to n
5514.
As the temperature of a transistor goes up the base-emitter resistance-
decreases
increases
remains the same
none
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: As temperature increase, the thermal runway properly of transistor becomes more prominent and base-emitter resistance will decreases.
5515.
A zener diode is destroyed if it-
is forward biased
is reverse biased
carriers more than rated current
none of the above
5516.
The most commonly used semiconductor is-
germanium
carbon
sulphur
silicon
5517.
The point of intersection of de and ac load lines is called-
saturation
operating
cut off
none of these
5518.
Noise factor of a ideal amplifier is---
0dB
5dB
0.5dB
10dB
Himalay Sen Sir
ইলেক্ট্রিক্যাল ডিপার্টমেন্ট Mcq
EEE MCQ
Electrical Department all question
বেসিক ইলেক্ট্রনিক্স all mcq
Besic electronics mcq
ব্যাখ্যা: ব্যাখ্যা: There is no noise in a ideal amplifier. So, noise factor is 0 dB
5519.
The reverse current in a diode is of the order of—
KA
A
mA
uA
5520.
If a power supply has no-load and full-load voltages of 30V and 25V respectively, then the percentage voltage regulation is:
10%
20%
15%
25%